English
Español
Русский
Français
|
Steam Bathroom Breakdown phenomenon and settlement:
|
||
|
Phenomenon
|
Reasons
|
Maintenance
|
|
Without steam
|
1. steam generator without water. 2. inside infrared pipe burn out of steam generator. 3. block of steam spray mouth. 4. probe out off control. 5. the temperature inside steam room is over the temperature what were set. 6. after fill into water it is still not the time for steam working. 7. it is overtime for the setting time. 8. unconnect with the control wire. |
1. check if the switch of water in be turn on or not. 2. change the infrared pipe. 3. get rid of mess. 4. check the connection wire and change the probe. 5. waiting decrease the temperature. 6. be waiting few minutes. 7. adjust the setting time. 8. connect to control wire. |
|
Without O3
|
1. system be damaged | 1. change the system |
|
Water pump unworking
|
1. water pump without power. 2. air pipe which connect with switch of air valve be insected untightly. 3. switch of air valve out of control. 4. air pipe leaking. 5. rotor of water pump unworking. 6. water pump be burned. |
1. check if the power of water pump get through. 2. to insect the air pipe tightly. 3. change the switch of air valve. 4. change the air pipes. 5. check if there are stems in the water pump,take apart those air pipes in order to get rid of stems. 6. change the water pump. |
|
Volume under control
|
1. suction of water pump is not enough. 2. air adjustment valve working abnormal. 3. block of jets. |
1. check the water pump if it is working normally. 2. change the air valve. 3. get rid of mess. |
|
Water pipe leaking
|
1. plastic seal ring be connected untightly. 2. screws unlock. 3.connection is glued not good. 4. water pipe be damaged. |
1. change the plastic seal ring. 2. screws should be installed tightly. 3. get rid of the PVC glue then stick. the glue again till it is be well done. 4. change the water pipe. |
|
Computer panel under control
|
1. power not be connected well,electronic leakage device without power. 2. switch of control panel out of control. |
1. get through the power again. 2. change the computer panel. |
|
Without lighting
|
1. bulb be burned. 2. without power. 3. switch of control panel out of control. |
1. change bulb. 2. get through power gain. 3. maintain or change the computer panel. |
|
Telephone connection unworking
|
1. telephone wire not connected well or be damaged. 2. telephone's device be blocked. |
1. check the wires of telephone and electronic box if get through or not, if there is something wrong replace. by the similar wires. 2. get rid of mess. |
|
Without sounds
|
1. speaker be broken 2. without power 3. switch of control panel out of control. |
1. change the speaker 2. get through power again. 3. maintain or change the computer panel. |
| Cleaning and Maintenance: 1. The daily maintenance of computerized steam room should be cleaned with ordinary detergent and wet cloth with toothpaste. Please do not use the detergent of disinfection which contains acetone or formaldehyde when operating disinfection. 2. If there are furring on the surface of bathtub, it can be take away try to wipe the bathtub with lemon juice or vinegar which be heated. 3. In order to avoid damaging the surface of products please do not use hardness and sharpness tool to curve the products. 4. Do not wipe the chrome plated spare parts all the time, and do not get in touch with chemical detergent etc. Otherwise the surface of chrome finish will be destroyed. The product should be clean by soft cloth other than coarse cloth. 5. To check the water pipe regularly in order to avoid troubles from crack of water pipes or blocked inside. 6.If there are something such as hair stuck inside the jets, then just to twist out the jets and remove it. 7. Suggest to add the filter of water quality in order to make sure the normal operate of products if the water quality is worse in the local area. 8. keep out from combustibles and goods which over 80'C to avoid fire disaster and damage the product. 9. Please let the professional to operate when the steam generator needs to be replaced. 10. If the bathtub has not been used for a long time, drain out water of the bathtub and keep it in a dry and ventilate environment. Avoid corrosive gas. |
||
|
Massage Bathtub Breakdown phenomenon and settlement:
|
||
|
Phenomenon
|
Reasons
|
Maintenance
|
|
No power or electricity leaking protection device is activated
|
1. Electricity leaking protection device cut off power source when electricity line is not well connected. 2. Power or electricity circuit have phenomenon of electricity leaking. |
1. check and reconnect the wiring system. 2. check the power source, electricity circuit and ground line. |
|
Water Jets are not working
|
1. check the system whether is on. 2. the impeller of water pump doesn't rotate. 3. water pump is broken which caused by working without water coming in. |
1. turn on the system. 2. check through and remove the garbage which is inside the pump. Switch pipe can be removed. 3.install a new water pump. |
|
The intensity of hydro-massage cannot be adjusted
|
1. water pump's suction has not enough power. 2. air adjustment valve is abnormal. 3. jets or nozzles are blocked. |
1. check the water pump whether is working normally. 2. change the air adjustment valve. 3. remove things which are blocking the jets. |
|
Water leaks from the pipes
|
1. seal ring is broken. 2. screws doesn't lock tightly. 3. pipes doesn't seal properly. |
1. chang seal ring. 2. lock the screws tightly. 3. re-seal the silicone. 4. change water pipe. |
|
Jets shower can not be work
|
1. voltage is abnormal 2. Switch cannot be work 3. control panel cannot be work. 4. water in electromagnetism valve is be blocked. |
1. please use it at the normal situation of voltage. 2. check and change the switch. 3. maintain and change the control panel. 4. get rid of mess of the jets. |
|
No lighting
|
1. The bulb is broken. 2. power line is disconnected. 3. control panel is broken. |
1. change a new bulb. 2. re-connect the circuit. 3. maintain or change control panel. |
| Cleaning and Maintenance: 1. The daily maintenance of whirlpool bathtub (massage bathtub), etc. should be cleaned with ordinary detergent and soft cloth. Please do not use the detergent which contains acetone or ammonia liquid. If there marks or something like glue on the surface of bathtub, just polish it with soft cloth dipping with gas. 2. If there are scratches on bathtub surface, please polish it with 1500# frosted paper dipping with liquid and burnish it with toothpaste. It will be shining again after that. 3. If there are furring on the surface of bathtub, it can be take away by mild acid detergent, for example wipe the massage bathtub with lemon juice or vinegar which be heated. 4. Do not wipe the chrome plated spare parts all the time, and do not get in touch with chemical detergent etc. Otherwise the surface of chrome plated will be destroyed. The product should be clean by soft cloth other than coarse cloth. 5. To check the water pipe regularly in order to avoid troubles from crack of water pipes or blocked inside. 6. If there are something such as hair stuck inside the jets, then just to twist out the jets and remove it. 7. To clean hydro-massage equipment: To full fill hot water which is 40'C, and pour 2g/L detergent, start hydro-massage function more than 5 minutes, then turn off the massage function and drain out the water. Next, to full fill cold water and start hydro-massage function for 3 minutes, then turn off the massage function and drain out the water, at last, to dry the bathtub with towel. 8. Filter should be clean once a week. 9. Keep out from combustibles and goods which over 80°C to avoid fire disaster and damage the product. 10. The bathtub should be transported carefully. Do not lay heavy things on it and do not bump and shaking the tub. If the bathtub has not been used for a long time, drain out the water of the bathtub and keep it in a dry and ventilate environment. Avoid corrosive gas. |
||
Q: How to Choose the Brand of Shower Room or Bathtub?
A: Brand is derived from customers’ supports and advertising’s spread. Brand is an advantage effect; it can be a certain extent to ensure product quality. In fact, a lot of products haven’t made advertisement, but they also sell well. This means, not only big brand can produce high quality products.
